The product you were looking for no longer exists! Here are products you may be interested in from the same category.
Protect your antenna base and maintain a clean seal with this antenna bezel gasket, designed specifically for 1963-1982 Chevrolet Corvette models. This factory-correct rubber gasket provides a snug fit around the antenna bezel, preventing…
This Corvette reproduction antenna nut has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
Will Not Fit ZR1
Reproduction of Original
…
Reproduction of Original
For Power Antennas
…
Manual Replacement for Power Antenna
Has Correct Finial on Mast
…
Reproduction Of Original
1963-64 Standard Antenna
1965-66 Power Antenna
…
This die cast, chrome plated spacer is angled.
The short side is 1/4 inch tall.
The tall side is 7/16.
O.D. = 1 5/16
I.D. = 3/4
There is a flange at the bottom which fits/snaps into gasket 162039
There is also a locator pin…
This C2 antenna nut has a thread size of 3/4 inch x 24.
…
Correct reproduction zinc diecast chrome plated antenna nut used on all 65-68 Corvettes.
This antenna nut cap has the correct flats on the side of the nut and stepped lower edge where the nut mounts on top of the antenna bezel.
Hole…
Reproduction of Original
Made in the USA
…
Reproduction Of Original
The mast section of the antenna consists of four round chrome sections, three telescoping sections, and one fixed section, with an approximately 1/4" ball-shaped tip at the end of the mast. The overall…
1963-1966 Corvette Antenna Body to replace your broken, misssing or rusted body.
…
Protect your investment with an Original Fender Gripper. They offer the highest degree of protection from impact and scratches while you work on your car. Each Fender Gripper is made from a unique reinforced foam padding that provides…
1969-1978 Corvette antenna mast retainer nut has 1/2 inch x 20 threads. Nut is 7/16 inch tall . Has 9/16 inch wrench flats. Top hole measures 0.414 inch ID.
RETAINING RADIO AERIAL MAST
…
8" Mast For Fixed Roof Coupes or Z06
Ideal Replacement For Cumbersome 29" Originals
Threaded Base Like Original/Excellent Reception
…
C3 CORVETTE MOUNTING RADIO AERIAL MAST…
Tapered mast as original (.100 at ball; .185 at mast).
Has correct .305 size ball.
This stainless steel antenna mast measures 31 1/2 inches overall length, with a thread size of 1/4 inch x 20.
…
Replacement Bezel
This Corvette replacement antenna bezel has been manufactured to meet or exceed factory specifications and performance. You will find the fit and finish will work perfectly for your Chevy.
…
OER® reproduction of the original GM AM/FM non-telescopic stainless steel fixed antenna mast for use on various GM models with an AM/FM radios including 1969 Camaros and Firebirds. Measures 30" non-retractable style round mast. Replaces…
Hangs from right hand radio knob.DECALS LABELS…
Rear Body Harness / Radio Antenna Cable
…
High quality stainless steel OER® reproduction of the original telescoping antenna mast for various GM models. Features include a round body and tip, and threaded end (with jam nut) that screws into the antenna base. Measures from…
RADIO AERIAL MAST MOUNTING…
Manual antenna assembly with 1967-1968 Corvette fixed length antenna mast and mounting hardware. Does not include cable.
…
Chrome flat style (non-domed) bezel nut which inserts under the antenna bezel nut on top of the fender. Applications: 1969 Camaro 1969 Firebird 1969-78 Corvette 1969 Impala/Full Size (non-power ant ennas) 1973-96 Impala/Full Size (power…
Reproduction Of Original
The most common electrical problem in a Corvette is a bad ground. The Corvette with its electrically non-conductive fiberglass body requires the use of ground straps for everything from preventing…
Reproduction of Original
Can Also be Used to Replace 1965-1966 Power Antenna
Use to replace missing, damaged or rusted base.
…
Antenna lower mount with clamp, screws and nuts.
…
OER® chrome antenna bezel nut which goes on top of the antenna bezel. Hole in nut is 9/16" id. Applications 1967-68 Camaro 1970-81 Camaro 1967-68 Firebird 1970-81 Firebird 1965-68 Corvettei> 1968-69 Chevy II / Nova (Front) 1965-67…
Clamps Antenna to Bracket on Inner Fender.RADIO AERIAL MAST BRACKETS…
Reproduction Of Original
Fits 1963-64 All
Fits 1965-66 Manual Antenna
…
Features:• Reproduction - Exact Of Original• CHROME NUT,BEZEL & RUBBER PAD FOR C6TZ-18813-A ANTENNA THESE PARTS COME WITH THE ANTENNA ASSEMBLY…