Installation may be simplified by using a UH-7 terminal end, or cutting wire at harness and reconnecting.
If old wire is damaged from engine heat, it can also be replaced with the insulation in this manner.
…
Maintain accurate engine temperature readings with this coolant temperature sender/sensor, designed for 1979-1980 Corvettes. This factory-correct sensor ensures reliable transmission of temperature data to your vehicle’s gauge or ECU…
(includes new asphalt loom, wire, terminal, & connector) TECH NOTES: Over the years, the terminal, connector, and wire to the temperature sending unit may have been altered by a previous owner or mechanic. This was not uncommon. This…
original 1/2 x 14 N.P.T.F. (correct resistance and connection produces accurate gauge display)
TECH NOTES: This Temperature Sending Unit converts engine temperature into electrical resistance, thereby producing a corresponding gauge…
Black woven insulation over temperature wire, with clip.
Includes:
Temperature Wire Terminal End
Temperature Wire End
Temperature Wire InsulationINSULATOR SENDING SENSOR WIRING…
original 1/2 x 14 N.P.T.F. all (correct resistance and connection produces accurate gauge display)
TECH NOTES: This Temperature Sending Unit converts engine temperature into electrical resistance, thereby producing a corresponding…
The variable resistor kit should correct almost any gauge that reads higher than the actual engine temperature. Install the resistor in line with your temp wire and set it to your engine temperature for gauge accuracy. It has a resistance…
The Engine Coolant Temperature Sender monitors the engine temperature. The engine temperature signal is used by the engine control module to adjust the air/fuel mixture and ignition timing. Male oval connector
81-84 Located in Front…
(includes new asphalt loom, wire, terminal, & connector) TECH NOTES: Over the years, the terminal, connector, and wire to the temperature sending unit may have been altered by a previous owner or mechanic. This was not uncommon. This…
with factory console gauges (includes new asphalt loom, wire, terminal, & connector) TECH NOTES: Over the years, the terminal, connector, and wire to the temperature sending unit may have been altered by a previous owner or mechanic…
(includes new asphalt loom, wire, terminal, & connector) TECH NOTES: Over the years, the terminal, connector, and wire to the temperature sending unit may have been altered by a previous owner or mechanic. This was not uncommon. This…
all 2nd design: VIN ending in 27373 to 49213, alarm switch located in driver side door lock cylinder & alarm horn located behind driver side front fender, near firewall (includes new wire, terminal, & connector) TECH NOTES: Over the…
This stock replacement outside air temperature sensor is manufacturedby GM or by one of its authorized suppliers for use as a factoryreplacement part. You will find the fit, finish and function meets allGM specifications. Using stock…
(includes new asphalt loom, wire, terminal, & connector) TECH NOTES: Over the years, the terminal, connector, and wire to the temperature sending unit may have been altered by a previous owner or mechanic. This was not uncommon. This…
Replacement Sensor
Black Wire Connector End
Solid Probe
1985-91 Located Under Plenum
1992-96 Located In Water Pump
For Computer Input
This Corvette replacement engine coolant temperature sensor has been…
Temperature Sender Unit Wire Repair Kit For
Chevrolet Camaro
Chevrolet Chevelle
Chevrolet Corvair
Chevrolet Corvette
Oldsmobile Cutlass
Chevrolet El Camino
Oldsmobile F85
Pontiac Firebird
Chevrolet Fullsize
Buick…
Replacement Sensor
Gray Wire Connector End
Open Probe
This Corvette replacement intake plenum manifold air temperature sensor has been manufactured to meet or exceed factory specifications and performance. You will…
original 1/2 x 14 N.P.T.F. all (correct resistance and connection produces accurate gauge display)
TECH NOTES: This Temperature Sending Unit converts engine temperature into electrical resistance, thereby producing a corresponding…
2 Wire repair pigtail
Replaces your factory pigtail that has been damaged by aging and heat. Pigtail connectors allow for more efficient, less costly wiring harness repairs. Wires are color coded and include plugs for easy…
This Corvette replacement air intake temperature sensor has been manufactured to meet or exceed factory specifications and performance. You will find the fit and function will work perfectly for your Corvette
Replacement…